CCNA MCQ Quiz and Online Test

Important Instructions:

Total Number Of Questions : 10
Passing Marks : 7
Each Question Carry 1 Mark, No Negative Marking.
Do Not Refresh The Page.
This Is A FREE Online Test, DO NOT Pay Money To Anyone To Attend This Test.
Best Of Luck…

Results

Congratulation…
You Have Passed The Test, You Should Try To The Next One…!!

Rate this post

Unfortunately…
You Did Not Pass. Why Not Try It Again?

Rate this post

#1. Which of the following is an example of a standard IP access list?

access-list 110 permit host 1.1.1.1

access-list 1 deny 172.16.10.1 0.0.0.0

access-list 1 permit 172.16.10.1 255.255.0.0

access-list standard 1.1.1.1

#2. You need to create an access list that will prevent hosts in the network range of 192.168.160.0 to 192.168.191.0. Which of the following lists will you use?

access-list 10 deny 192.168.160.0 255.255.224.0

access-list 10 deny 192.168.160.0 0.0.191.255

access-list 10 deny 192.168.160.0 0.0.31.255

access-list 10 deny 192.168.0.0 0.0.31.255

#3. You have created a named access list called Blocksales. Which of the following is a valid command for applying this to packets trying to enter interface s0 of your router?

(config)#ip access-group 110 in

(config-if)#ip access-group 110 in

(config-if)#ip access-group Blocksales in

(config-if)#blocksales ip access-list in

#4. Which of the following are valid ways to refer only to host 172.16.30.55 in an IP access list? (Choose two.)

Select all that apply:

172.16.30.55 0.0.0.255

172.16.30.55 0.0.0.0

any 172.16.30.55

host 172.16.30.55

#5. Which of the following access lists will allow only HTTP traffic into network 196.15.7.0?

access-list 100 permit tcp any 196.15.7.0 0.0.0.255 eq www

access-list 10 deny tcp any 196.15.7.0 eq www

access-list 100 permit 196.15.7.0 0.0.0.255 eq www

access-list 110 permit ip any 196.15.7.0 0.0.0.255

#6. What router command allows you to determine whether an IP access list is enabled on a particular interface?

show ip port

show access-lists

show ip interface

show access-lists interface

#7. Which router command allows you to view the entire contents of all access lists?

Router#show interface

Router>show ip interface

Router#show access-lists

Router>show all access-lists

#8. If you wanted to deny all Telnet connections to only network 192.168.10.0, which command could you use?

access-list 100 deny tcp 192.168.10.0 255.255.255.0 eq telnet

access-list 100 deny tcp 192.168.10.0 0.255.255.255 eq telnet

access-list 100 deny tcp any 192.168.10.0 0.0.0.255 eq 23

access-list 100 deny 192.168.10.0 0.0.0.255 any eq 23

#9. If you wanted to deny FTP access from network 200.200.10.0 to network 200.199.11.0, but allow everything else, which of the following command strings is valid?

access-list 110 deny 200.200.10.0 to network 200.199.11.0 eq ftp access-list 111 permit ip any 0.0.0.0 255.255.255.255

access-list 1 deny ftp 200.200.10.0 200.199.11.0 any any

access-list 100 deny tcp 200.200.10.0 0.0.0.255 200.199.11.0 0.0.0.255 eq ftp

access-list 198 deny tcp 200.200.10.0 0.0.0.255 200.199.11.0 0.0.0.255 eq ftp access-list 198 permit ip any 0.0.0.0 255.255.255.255

#10. You want to create a standard access list that denies the subnet of the following host: 172.16.50.172/20. Which of the following would you start your list with?

access-list 10 deny 172.16.48.0 255.255.240.0

access-list 10 deny 172.16.0.0 0.0.255.255

access-list 10 deny 172.16.64.0 0.0.31.255

access-list 10 deny 172.16.48.0 0.0.15.255

CHECK ANSWER

Rate this post